Europe based Mega-Store of RC Helicopters, Drones, Planes

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7445 was designed specifically for airplanes requiring a 150cc - 170cc equivalent gas engine, or other airframes requiring up to 10,000w of power.

Recommended Prop Selection :

For 12s - 30x12C2E - 33x10C2E = 150cc performance

For 14s - 28x12C2E - 30x12 C2E = 150cc performance

Recommended ESC -: Tribunus II 14-300A ESC SBEC

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty.
Precautions must be taken. We recommend the use of an additional capacitor bank such as the APD 100V 800uF.

Acrobatic Weight Range -: 15.0kg - 25.0kg - kg (33.0lbs - 55.0lbs)

Sport / UAV (single engine) Weight Range : - 21.5kg - 64kg (47.4lbs -142.0lbs)

Specifications

Motor Kv 140 RPM / Volt
Weight (Motor only) 1688g (59.54 oz)
Weight (including prop mount accessories) 1808g (63.77 oz)
Motor Body Dimensions 86.80 mm x 85.30mm (3.42" x 3.36")
External Shaft Diameter 10mm
Continuous Current 136A
Continuous Power 7100 Watts
Peak Current* 192A
Peak Power* 10000 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 45 mm (1.77 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 5T/6T 4Y
Motor Wire 1.25mm

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7441 was designed specifically for airplanes requiring a 100cc - 126cc equivalent gas engine, or other airframes requiring up to 9,300w of power.

Recommended Prop Selection :

12s Lipo - 28x13E, 29x12E, 30x12E

14s Lipo - 27x12E, 28x10E

Recommended ESC : Tribunus II+ 14-200A ESC SBEC + Scorpion 40mm High Speed Cooling Fan V2

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 165 RPM / Volt
Weight (Motor only) 1605g (56.61 oz)
Weight (including prop mount accessories) 1717.0g (60.56 oz)
Motor Body Dimensions 86.80mm x 81.90mm (+20.0mm prop hub) (3.42" x 3.22" (+0.79 prop hub))
External Shaft Diameter 10mm
Continuous Current 120A
Continuous Power 6260 Watts
Peak Current* 178A
Peak Power* 9300 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 41.6 mm (1.64 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 5T 4Y
Motor Wire 1.35 mm
No-Load Current (IO/15V) 3.49 Amps

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7441 was designed specifically for airplanes requiring a 100cc - 126cc equivalent gas engine, or other airframes requiring up to 9,000w of power.

Recommended Prop Selection :

28x12 C2E = Optimal / 120cc performance

28x13 C2E = High Alt

Recommended ESC : Tribunus II+ 14-200A ESC SBEC + Scorpion 40mm High Speed Cooling Fan V2

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 180 RPM / Volt
Weight (Motor only) 1555g (54.85 oz)
Weight (including mount + Prop mount accessories) 1725g (60.84 oz)
Motor Body Dimensions 86.80mm x 81.90mm (3.42" x 3.22")
External Shaft Diameter 10mm
Continuous Current 141A
Continuous Power 6260 Watts
Peak Current* 202A
Peak Power* 9000 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 45 mm (1.77 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 4T/5T Y
Motor Wire 1.35 mm
No-Load Current (IO/15V) 3.49 Amps

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 250C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7430 was designed specifically for airplanes requiring a 70cc-85cc equivalent gas engine, or other airframes requiring up to 7500w of power.

Recommended Prop Selection :

For 12s - 28x12 C2E / 28x13 C2E // 100cc performance

For 14s - 25x12E / 26x12E // 85cc performance

Recommended ESC : Tribunus II+ 14-200A ESC SBEC

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 155 RPM / Volt
Weight (Motor only) 1271.0g (44.8 oz)
Weight (including prop mount accessories) 1367g (48.21 oz)
Motor Body Dimensions 86.80mm x 70.4mm (+20.0mm Prop Spacer) (3.42" x 2.77" (+0.79" prop spacer))
External Shaft Diameter 10mm
Continuous Current 110A
Continuous Power 5328 Watts
Peak Current* 150A
Peak Power* 7500 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 7T 4Y
Motor Wire 1.12mm dia
No-Load Current (IO/20V) 2.54A

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 250C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7430 was designed specifically for airplanes requiring a 70cc-85cc equivalent gas engine, or other airframes requiring up to 7500w of power.

Recommended Prop Selection :

For 12s - 25x12E / 26x12E // 85cc peformance

Recommended ESC : Tribunus II+ 14-200A ESC SBEC

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 185 RPM / Volt
Weight (Motor only) 1255.0g ( 44.2 oz)
Weight (including prop mount accessories) 1351g (47.65 oz)
Motor Body Dimensions 86.80mm x 70.4mm (+20.0mm Prop Spacer) (3.42" x 2.77" (+0.79" prop spacer))
External Shaft Diameter 10mm
Continuous Current 120A
Continuous Power 5328 Watts
Peak Current* 169A
Peak Power* 7500 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 6T 4Y
Motor Wire 1.2mm dia
No-Load Current (IO/20V) 2.54A

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand 1.18mm enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

Recommended Prop Selection :

24x10E / 24x13E (Carbon) / 25x12E / 26x8E

Recommended ESC -: Tribunus II+ 14-200A ESC SBEC

Acrobatic Weight Range -: 8.18kg - 12.7kg (18.0lbs - 28.0lbs)

Sport / UAV (single engine) Weight Range : - 12.7kg - 36kg (28.0lbs -80lbs)

Specifications

Motor Kv 160 RPM / Volt
Weight (Motor only) 998g (35.20 oz)
Weight (including mount + Prop mount accessories) 1115g (39.33 oz)
Motor Body Dimensions 78.5 mm x 67.8mm (3.09" x 2.67")
External Shaft Diameter 10mm
Continuous Current 80A
Continuous Power 4218 Watts
Peak Current* 124A
Peak Power* 6450 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 65.0 mm (2.56 in)
Stator Thickness 28 mm (1.10 in)
No. of Stator Arms 12
Magnet Poles 14
Motor Wind 8T Delta
Motor Wire 2-Strand x 1.12mm
No-Load Current (IO/20V) 1.9 Amps
Motor Internal Resistance 11.4 mΩ


*Our ratings are classified as TRUTHFUL. Continuous Current / Power correlates to actual sustainable power levels. Peak Power is for intermittent full throttle usage ranging from 5 - 60 seconds depending on use case and cooling*
**Higher Cell Count possible with smaller prop usage**

Included in the Box
1 x Scorpion A-6528 BLDC Motor
1 x A-55/65 Cross Mount (stock)
4 x M4 Cross Mount Mounting Bolts
3 x Female 6mm Connectors
3 x Heat Shrink
3 x Scorpion Stickers
2 x M10 Nuts

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand 1.18mm enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-6528-180kv was designed for 90"- 95" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 7200w of power. Compared to the -200kv version, this motor is designed to swing a larger / slower spinning prop in the 24" - 26" range on 12s battery.

Recommended Prop Selection :

24x10E / 24x13E (Carbon) / 25x12E / 26x8E

Recommended ESC -: Tribunus II+ 14-200A ESC SBEC

Acrobatic Weight Range -: 8.18kg - 12.7kg (18.0lbs - 28.0lbs)

Sport / UAV (single engine) Weight Range : - 12.7kg - 36kg (28.0lbs -80lbs)

Specifications

Motor Kv 180 RPM / Volt
Weight (Motor only) 998g (35.20 oz)
Weight (including mount + Prop mount accessories) 1115g (39.33 oz)
Motor Body Dimensions 78.5 mm x 67.8mm (3.09" x 2.67")
External Shaft Diameter 10mm
Continuous Current 95A
Continuous Power 4218 Watts
Peak Current* 162A
Peak Power* 7200 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 65.0 mm (2.56 in)
Stator Thickness 28 mm (1.10 in)
No. of Stator Arms 12
Magnet Poles 14
Motor Wind 7T Delta
Motor Wire 2-Strand x 1.18mm
No-Load Current (IO/20V) 2.39 Amps
Motor Internal Resistance 6.85 mΩ


*Our ratings are classified as TRUTHFUL. Continuous Current / Power correlates to actual sustainable power levels. Peak Power is for intermittent full throttle usage ranging from 5 - 60 seconds depending on use case and cooling*
**Higher Cell Count possible with smaller prop usage**

Included in the Box
1 x Scorpion A-6528 BLDC Motor
1 x A-55/65 Cross Mount (stock)
4 x M4 Cross Mount Mounting Bolts
3 x Female 6mm Connectors
3 x Heat Shrink
3 x Scorpion Stickers
2 x M10 Nuts

Direct Upgrade to Pitch rods, Stronger and lighter.

Titanium Gr5 Linkage rod SET with counter threads, made from Titanium, Rolled tread M3.

Usually, we can't fine-tune a typical ball linkage set to any length because we need to turn the ball link a whole or multiple rounds.
In order to keep the direction of the ball link.

Now we solve this problem. With the two-way fine adjustable linkage rods, you are able to fine-tune the linkage length without taking off the ball link.
The helicopter setup is no more a bothersome process!!

Unparalleled durability and performance without compromise
Weight roughly 45% less than steel turnbuckles
Meticulously engineered to excel under the most demanding conditions
CNC-machined from high grade Gr5 billet Titanium

Pack include 2 rods

See the other images to understand the tech drawing sizes.

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diversity, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link

The Crossfire Micro TX borrows the core technology from its larger brother, but is a JR-module transmitter simplified to the most sought-after features, at a killer price! For people looking to do extreme long range flights beyond 15-20km, the Crossfire TX is still the way to go. For anyone looking to penetrate buildings, fly mini quads or just explore your surroundings a few kilometers away, the Micro TX is the perfect companion. It will still go out up to 40km, just like its bigger brother. But it costs less than half the price.

 Features:

•     Long range, adaptive and robust remote control system for your aircraft
•     Immune to on-board noise
•     Two-way communication link with real-time link vitals and telemetry
•     Self-healing & frequency hopping (DSSS, FHSS)
•     Adaptive bandwidth control and range optimization
•     RX beacon mode to recover your downed aircraft
•     Super easy binding and configuration via built-in display of your R/C
•     Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
•     Two receiver models: 8 port Diversity Rx, 4 port Mini-receiver (4g weight!)
•     8 or 12ch output via SBUS/PPM/CRSF on both receivers
•     Ability to fly with multiple friends at the same time (10 or more)
•     Selectable RF power from 25mW to 250mW (local restrictions apply)
•     Transmitter LED shows link health
•     Micro-receiver for smaller drones. Smaller than you think!
•     Software updates via RF Link

 
Technical specifications:

•     Frequency Band: 868MHz- EU
•     Input Voltage: 6.0 - 13V
•     Connector : USB-C
  
•     Power consumption: 1.1W (@10mW) - 2W (@100mW)
•     Dimensions: 65 x 48 x 22 mm (JR module size)
•     Weight: 48g

Package includes

• 1 x TBS Crossfire Micro TX V2
• 3 x TBS Crossfire Nano RX
• 3 x TBS Crossfire Micro Receiver Antenna
• 3 x TBS Crossfire Immortal T V2 Antenna
• 1 x Taranis QX7 Mod
• 3 x Cables and Shrink Tubes set

The LiPo Safe sack/bag is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.

This is a long version of the Safe product, measuring internal dimensions of 340x70x65mm, fits long Stick Lipos 12s and even some 14S packs- verify the size of your lipo to be sure it fits inside the bag.

The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap

Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.

Instructions to use:

Ensure that charger rate is properly set and polarity is correct

1. Attach charging leads to battery
2. Place battery in LiPo Safe towards the bottom
3. Place LiPo Safe on non-flammable surface
4. Route charge leads through vent at the top seam of the LiPo Safe
5. Close top flap of LiPo Safe and press hook and loop closure fully closed
6. Charge battery using proper charging practices
7. Always practice extreme caution when charging and never leave a charging battery unattended

Please check the Video showing the use of Lipo Safe

This is a pack of 8 RCPROPLUS SUPRA-X REB6808 PRO D6 6mm Bullet Connector

Set including 8 PAIRS.

Featuring a unique patented banana plug lock design, these Pro-D6 connectors securely lock in place handling quick movements and vibrations, commonly found during extreme 3D flights, without coming apart. The stronger jacket and snaps extends the advantages of the previous generation of Supra X Connectors and makes them better.

These connectors are a great solution for your high current and high voltage demands offering a large, low resistance surface patch for efficient power transfer. The 24K Gold Plated bullet plugs feature a recessed wire cavity and solder windows making assembly hassle free, while the sheath uses high temperature capable, impact-resistant plastic imported from Japan.

Cover material:IDEMITSU plastic
Banana connector diameter:6mm
Suggested Wires:8AWG-10AWG
Capacity (Continuous):200A
Capacity (Burst):240A
Banana connector material:Class A Cooper C54 Series
Plating:24K Gold / Flash

Features:
Connection between battery and ESC
Can be used for 4 batteries and 4 ESCs (or 4 charger cables)

Package Included:
4 x Set
8 x 6mm Female& Male Bullet Connector

FPV x230 Racer With Gimble,1080P Wide Angle HD Camera RC Quadcopter RTF

• Built-in 120° wide angle and 1920 x 1080P HD camera to get the high quality shooting;
• Equipped with 2200mAh smart flight battery.
• Flip 360° steadily;
• Real-time transmission for FPV action video.

Remote control:

• Built-in video transmitter to improve the transmission quality and reliability of communication;
• Equipped with camera and operation button to control easily.

Package Included:

• 1 x X230 Multicopter
• 1 x Battery
• 2 x ABS 5030 propeller
• 1 x Balance charger
• 1 x Charger cable
• 1 x Adapter
• 1 x 4 pins connection wire
• 1 x Screw bag

Soldering Station ZD-937, black, 150°C - 450°C, 48W,ESD-protection, with pre-selection buttons 100, 200, 300°C.

The station is ideal for home elektronics, school, workshop, service, production and lab.

Among the easy and quick temperature adjustment with the up-/down-buttons in 1°C- and 10°C-steps, it is possible to pre-select 100°C, 200°C and 300°C with the related button.

• Compact, solid and insulated housing.
• Station and soldering iron pod are arrangeable seperately.
• Complete with soldering iron pod and soldering sponge.
• LCD display with ilumination shows must- and actual value.
• Energy display
• 3 pre-selectionable fixed temperatures
• Electronical sensor
• Temperature controll
• Short heating-up time thanks to its generous designed power supply
• Powerful 48W soldering iron for a wide range of application
• Temperature adjustment with buttons from 150 to 450°C, 1°C and 10°C steps
• Optical and accoustic error message in case of malfunction
• ESD protection

Technical Specification:

• Input Voltage: 230V (220-240V), 50 Hz
• Power of soldering iron: 48W
• Fuse: T 1A/250V
• 150°C-450°C temperature adjustment with 1°C- and 10°C-steps
• Display accuracy: 5%
• LC-Display with 3 1/2 digits
• Dimension WxHxD: 210x125x135mm
• Weight 1,8kg

Delivery:

• Soldering station ZD-937
• Soldering iron pod with drawer and soldering sponge
• Soldering iron with tip 1,6 mm
• German and english manual

This "economy" spanner set includes just about all the sizes you will ever need on a model heli.
Ideal for you field box and building bench.

Sizes included are : 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm.
Set of 10 spanners

TITAN DC5 w/ DJI Air Unit BNF built for  the amazing new DJI FPV system, this quad makes flying FPV truly breathtaking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This TITAN DC5 BNF is 5 inch quad which is no prop in view, equipped SucceX-D F7(50A 4-in-1 ESC) Stack and popular XING motor, everything you just need to bind and fly!

This model can accept up to 6s, but the motors mounted are designed to be used with 4S.

You can use Any radio you want, you will need to add your receiver and bind and calibrate it.

If you use your own DJI Remote Controller, you need to update beta-flight to 10.6.0 to set up and bind your DJI remote controller.

ELECTRONICS // SucceX-D F7 Stack (50A 4-in-1 ESC):

• Universal USB Type C connector instead of micro USB
• Plug-and-Play. No need to solder tiny wires
• Designed to support DJI Digital FPV.

BNF // Parts lists

• 1x TITAN DC5 HD Frame
• 2x TPU camera side plate soft mount
• 1x iFlight Lipo Strap
• 2x Nazgul 5140 Propeller (Set of 4 - Color May Vary)
• 4x XING 2207 Motor Unibell (4S 2450KV)
• 1x SucceX- F7 Flight Controller
• 1x SucceX BLHeli32 50A 4-in-1 ESC 2-6S

Sky hero Anakin Club FPV racer 215mm -5"’’ ARF combo, Our combo delivered with Best components we beleive are on the market today. We beleive that quality assembly can be done by customer, there are a lot of advantages to do so.
See the specs below.

• Anakin club racer Frame kit Xnova 2204-2300Kv motors, esc, props- Included and factory preinstalled.
     Note: if you choose other motors, you will need to assemble the kit yourself, you will receive all components, but not ARF version.
• CC3D Metal Case controller included
• PDB-Bec
• FPV Camera included
• RADIO link AT9 with receiver Sky hero version (white edition )

Not included:

• Lipo charger
• Battery 3s 1300-1500 mah
• VTX - optional

Sky hero did it again, with the latest drone technology, you have the possibility to fly the freedom of birds.
With competition racing and performance within the DNA of SKY HERO, this machine was created as serious racer for those who want the best.
Club-racer- inherits the amazing design of the original sky hero Anakin, with new evolved concept.
Strengthened with flat arms.
this was developed with the vision that FPV racers deserve a near-indestructible machine, agile racer they can trust.
Locked in trajectories and customizable.

General specs of Club racer versions.

• Full carbon frame- Crash resistant.
• Innovative abutted A frame design.
• Minimized vibrations distribution, Optimized shock absorption
• 3K 4mm Carbon
• Sandwitched frame plates

• Fully protected electronics
• Optimized Shape, size and frame thickness, delivering outstanding strength-to weight ratio
• Responsiveness- so rigid, that you feel "At one" with your frame.

ESSENTIALS

•     Entirely designed for racing
•     Flat arms conception for highest impact resistance
•     Simplified option for easy components replacement
•     Low drag, for higher speeds
•     Electronics fully protected

KEY FACTORS

•     Premium choice for FPV
•     High wind resistance
•     Super fast